How To Install A Delta Shower Valve Rough In
Delta shower valve installation doesn't have to exist hard.
That said, if local plumbing lawmaking requires the utilize of copper, this tutorial will be a huge help.
At that place are tons of tips that'll make your projection much easier, so let'south dive in!
Delta Shower Valve Installation Supplies
Here are the supplies used in this projection:
- Delta MultiChoice Rough-In Valve
- Bernzomatic MAP Gas
- TS400 Trigger Get-go Torch
- H-20 Water Soluble Flux
- Acid Brush for Flux
- Oatey Safe-Flo Solder
- Emery Material
- Nylon Grit Pads
- Ridgid Deburring Tool
- Sioux Chief AA MiniResters (Water Hammer Arrester)
- Type Fifty 1/two″ Copper
- Flame Protector Pads
Don't worry, I'll show you how to utilize all these materials.
How to Set up Delta Shower Valves to Right Depth
Setting any shower valve to the right depth is important.
Attach a scrap piece of the capitalist board to the stud walls. Then dry fit the tile being used and place the valve inside the wall (flush with the adjacent wall).
Go the measurement from the end of the plaster guard to the finished wall.
This measurement is the depth of the wood blocking that's needed to fix the valve at the right depth.
Delta valves typically simply need a piece of 2×4 or 2×ten dimensional lumber, which tin can be nailed or screwed to studs.
Connect Copper Riser Pipe to Delta Valve
The beginning step to installing a Delta shower valve is to connect the riser pipage.
Deburr and prep the copper pipe with emery cloth or nylon grit pads.
And then apply the Oatey H-20 flux to both the piping and drop-ear elbow; this is a great option because it'due south water-soluble.
In addition, the water lines won't demand to exist flushed when using H-20 flux.
I like to overhang the pipe on two pieces of 2×6 and solder it with a torch.
This keeps the workspace safety and provides ample working room for the torch.
Let that absurd and wipe off whatsoever backlog flux.
How to Prep Copper Pipes for Delta Shower Valve
Copper pipe prep is the key to getting nifty soldered joints.
The kickoff step is to deburr both the inside and outside of the pipe.
Then to use either emery fabric or nylon grit pads to clean the copper.
Fittings are normally very clean just information technology doesn't hurt to apply a wire brush.
Finally, employ a thin layer of the Oatey H-twenty flux to the pipe and plumbing equipment. In one case the fitting is placed on the piping, wipe off any backlog flux.
This last tip will help you become awesome-looking soldered joints.
How to Solder Copper Pipes to Delta Shower Valves
It's good exercise to start the heat at the lesser and piece of work upward.
Therefore, I recommend heating the couplings first then working up toward the valve.
Likewise, pre-oestrus the first half-inch of the copper pipe (just for a few seconds) and then utilise heat to the plumbing equipment.
Dab the solder on the fitting/pipage connection and once it starts to melt, remove the heat.
This admittedly takes some practice, so information technology never hurts to do just that – practice with spare pieces of copper and fittings.
Watch this total tutorial to see all the steps for a Delta shower valve installation with copper pipe
What's Next
Hopefully, the tips in this tutorial aid you with your shower remodel. If your side by side footstep is to waterproof the shower, this Schluter tutorial might aid out.
If you lot're doing a bath remodel and need help, join one of my step-by-step online courses – it'll brand your bathroom renovation much easier!
Allow me know if you take whatsoever questions and I'll do my best to assist.
Hope y'all take an crawly mean solar day!
Cheers,
Jeff
Small Bathroom Remodel Tips
Source: https://homerepairtutor.com/delta-shower-valve-installation-tips/
Posted by: sturtevantsoliften.blogspot.com
0 Response to "How To Install A Delta Shower Valve Rough In"
Post a Comment